Here is Nissan CONSULT III plus 73.20.00

• Nissan Consult 3 Software Cracker Tool
• Nissan Consult 3 Software Cracker Download

Download link is shared from http://mhhauto.com/Thread-CONSULT-III-plus-73-20-00

YOU ARE TRYING ON YOUR OWN RISK

For sake of security, you’d better use the link http://www.cardiagtool.co.uk/nissan-consult-iii-plus-nissan-security-card-for-immobilizer-1325.html

Consult 3 plus v73 FAQs:

Q: Is the any one can say about programming key without security card ? is it possible or not ?

A: Yes. It’s possible.

Nissan Consult 3 is a diagnostic software special for Nissan,support all the models of the Nissan and Infiniti from 1996 up till now, with all Consult II & III functions.It can support all Nissan car,Infiniti carand Nissan GTR. Nissan Consult 3 Plus Functions List. Nissan Consult 3 crack Consult III software configure maunal Nissan Consult 3 is can. 3 crack Consult III software. Crack Nissan Consult III software. Nissan Consult 3 III Setup Instruction 1) Open Consult III CD, click 'consult iii setup.exe'. 2) Click 'Next'. Nissan Consult 3 III Free Download and Installation I. Software and crack in.

Q: So which version is able to programming key without security card ?

A: 72.20 is your bet. But you need to modify

Q: I tried to reprogram the ABS module for a 2009 Nissan Murano but reprogramming option was disabled(Gray). any body knows how to activate it?

A: you need to edit the file DiagnoticTool.ini to enable reprogramming and also IMMO. Or if you have money to waste buy the reprogramming card and the NATS card. Add the following line to the DiagnosticTool.ini file

[mode]
debug_mode=TRUE
debug_mode_vehicle-battery=TRUE
[vehicles]
tab_index=0

also make sure system management access_mode is set to 1. That should give you full access. That’s not to say that it will work if you do not have the correct calibration file in the reprogramming folder on the C drive. good luck

Review:

I was able to update 2013 Altima 2.5 ECU using this software and genuine

Adobe photoshop keygen. Nissan Toughbook and VI2, also works with Dell D630 32 or 64 bit W7.

Just run the 4 setups, after install completes, copy and save the 10 gigs in the

ReproProgramming folder to another location, then delete all files in that

folder. Then copy over the Dat and Csv files into the ReproProgramming

folder. Then just follow the programming steps in Consult 3 plus as there

are quite a few. Make sure your power supply can maintain system voltage

while programming, mine started out at 13.5 but after a few minutes dropped

to 12.5, the spec is 12.0-13.5. The procedure takes a full 10 minutes.

I tried several versions of Consult 3 plus software, they worked fine for

scanning, but when trying Ecu programming, the Program buttons

were all greyed out. Allscript training manual. This version worked.

Have fun

(12.2018) FREE download Nissan Consult 3 Plus latest version 83.11.00 and 81.11.00 software:

CONSULT 3 Plus v83.11.00:

CONSULT III Plus v81.11.00:

Nissan Consult3 old patch download free:

This is used for it cannot be patched with “C3PCheckLicense” file

Remove old patch and install Consult 3 here Samsung scan assistant mac.

Test: Consult 3 plus 83.11 does not work with j2534 PassThruSupport.04.04 devices, only API 05.00…… but Consult 3+ 81.11 no problem

Go back to version 75 if you want programming

Nissan Consult III plus v75 software download:

CSP Software Version : CSP V41.10

Programming Data Version : Plus_V75

Password: Not required

Installation tip:

Uninstall the firewall, antivirus software.

Install the Consult 3 plus V75.20 to the C drive in the “NTFS” format.

Security: use with relief, 100% tested with Consult 3 plus china clone!

Languages: English/ French/ German/ Spanish/ Italian/ Japanese/ Portuguese/Russian/ Finnish/ Greek/ Chinese(Simplified)/ Chinese(Traditional)

Vehicles: Nissan and Infiniti from 1996 to 2017

Programming: confirmed! ECU Programming without card

Kts570 working with Consult III plus:

Have to modified the INI.

[current_channel]
channel=0

[system_management]
access_mode=1

[device]
vi_device_name=J-box 2
[mode]
debug_mode=TRUE
debug_mode_vehicle_battery=TRUE
[vehicles]
tab_index=1

“tab_index=1” seems the key to make jbox2 especially. Another thing is that you don’t need change the name of Jbox2 folder to nissan_VI2. Just copy the name of device (in this case “J-Box 2″) and paste to the vi_device_name in INI file. so it gonna be vi_device_name-J-Box 2”. That is it. At the first time, I changed the name of the folder in regedit, and errors showed. Now, automatically consult3 recognized jbox2 and vin number now. Only DTC and clear codes were detected though so far. I did not dig deeper yet.

Nissan Consult 3 Software Cracker Tool

For KTS570, it is pretty much same as jbox2. The difference is that I wrote “tab_index=4” instead of ‘1’. You also need update the firmware through esi. Otherwise, consult3 did not recognize.

Nissan Consult 3 Software Cracker Download